• ARC BX1 Coarse Abrasion Resistant Lining
enquire
ARC BX1 coarse abrasion resistant lining application

This high build – single coat application is a modified epoxy formulation for coarse-particle, severely abrasive, sliding wear environments

ARC BX1 Coarse Abrasion Resistant Lining

This technology is a 100% solids, VOC free modified epoxy formulation. It's reinforced with a proprietary blend of ceramic beads and powders

ARC BX1 coarse abrasion resistant lining application
ARC BX1 Coarse Abrasion Resistant Lining

ARC BX1 Coarse Abrasion Resistant Lining is a modified epoxy trowel-grade coating.

It is specifically formulated for coarse-particle, severely abrasive, sliding wear environments.

This is a 100% solids, high build – single coat application that delivers a high adhesive strength, allowing for vertical build capability to most substrates. This abrasion resistant lining is a VOC free coating which is reinforced with a proprietary blend of ceramic beads and powders for the repair and protection of all metal surfaces subjected to severe abrasion and impact. It provides long-term abrasion resistance, extending the operating life of equipment and it also lowers the coefficient of thermal expansion.

ARC BX1 Coarse Abrasion Resistant Lining additionally provides chemical resistance to a broad range of chemical exposures.

It’s a no VOCs, no free isocyanates application, allowing it to be applied safely in confined areas.

ARC BX1 Coarse Abrasion Resistant Lining is designed to:

  • Protect areas exposed to sliding abrasion
  • Resurface damaged metal in lieu of more traditional weld overlays
  • Replace ceramic tiles and rubber linings, which can disbond easily
  • Safely and easily apply by trowel

ARC BX1 Coarse Abrasion Resistant Lining application areas include:

  • Bins and silos
  • Blow lines
  • Pipe elbows
  • Apex cones
  • Hydro​pulpers
  • Exhausters
  • Slurry pumps
  • Chutes
  • Transport screws
  • Wear plates
  • Cyclones
  • Pneumatic transport lines
enquire
Mix Ratio A:B By Weight 2.3 : 1
Working Time 1.5 litres is 68 mins at 16°C (60°F)

5 litres is 50 mins at 16°C (60°F)

20kg (44lbs) is 35 mins at 16°C (60°F)

Curing Schedule Tack Free at 16°C (60°F) is 7 hours

Light Load at 16°C (60°F) is 16 hours

Full Load at 16°C (60°F) is 30 hours

Full Chemical at 16°C (60°F) is 72 hours

Pull Off Adhesion (ASTM D 4541)

210 kg/cm² (20.7 MPa)

>3000 psi

Vertical Sag Resistance

at  21°C (70°F) and 6mm (1/4″)

No Sag
Maximum Temperature

(Dependent on service)

Wet Service is 95°C (203°F)

Dry Service is 205°C (400°F)

Cured Density 2.3 g/cc

144 lb/ cu.ft.

Packaging and Coverage
Nominal, based on a 6000 microns (240 mil) thickness
1.5 litre kit covers 0.25 m² (2.69 ft²)

5 litre kit covers 0.85 m² (8.97 ft²)

20 kg kit covers 1.45m² (15.6 ft²)

ARC 858 high strength bonding polymer seals, shims and bonds new plates to a prepared surface on an offshore platform

Plate Bonding – Cactus ARC 858

Live Leak Sealing A Drains Line

The Bristle Blaster surface preparation tool is used in pipeline maintenance and repair

Bristle Blaster, Steel Construction

View Similar Products...

ARX BX2 Industrial Wear Resistant Coating protects impellar from erosion, corrosion and chemical attack

ARC BX2 Industrial Wear Resistant Coating

ARC BX2 Industrial Wear Resistant Coating is a modified epoxy trowel-grade Coating. It's reinforced for fine particle, abra

Aggregate is added to the wet ARC 855 Chemical and Corrosion Resistant Coating to ensure greater adhesion when further layers are applied in this repair project

ARC 855 Chemical and Corrosion Resistant Coating

ARC 855 Chemical and Corrosion Resistant Coating is a chemically-resistant thin film coating. It features moderate ceramic re

PMMA-Based Anti-Skid Wearing Layer solution for offshore decks and walkways is applied by hopper gun

PMMA-Based Anti-Skid Wearing Layer

PMMA-Based Anti-Skid Wearing Layer is a rapid curing highly abrasion-resistant coating ideally suited for offshore decks and

Need more info on our coatings & composites?

contact us